98 Vw Beetle Headliner Installation

You search Content 98 Vw Beetle Headliner Installation, If search results do not exist,please search by others keyword.

Convereting VW Beetle from 6 volt to 12volt

This is a great article by Speedy Jims. US VW s had 6 Volt systems up through the 1966 model year. Often, it’s desirable to convert these cars to a 12 Volt system.

VW Beetle Dash | eBay

Find great deals on eBay for VW Beetle Dash in Dash Parts. Shop with confidence..

1999 Volkswagon Beetle headliner replacement

Step by step installation instructions for removing, recovering and replacing the headliner in a 1999 Volkswagon Beetle. The original headliner started sagging in.

2002 Honda Civic DX Sedan L4-1668cc Headliner Removal/Installation


Filed Under (Honda) by admin on 07-04-2015

download NOTE: Use the suitable instrument from the KTC trim instrument set to keep away from injury when prying components. When prying with a flat-tip screwdriver, wrap it with protecting tape to stop damage. Take care to not bend and scratch the headliner. Be careful to not harm the dashboard and other inside trim. 1. Take away these items: – A-pillar trim, both sides. – B-pillar higher trim, one side, 2-door. – B-pillar higher trim, either…

New Beetle Headlamps Removal and Installation Volkswagen 1998-2008 :- Manual repair.


Filed Under (Volkswagen) by admin on 14-04-2014

download Note: Removal and installation of right headlamp is illustrated. Removal and installation of left headlamp is the same. Special tools, testers and auxiliary items required 5 mm hex socket wrench Removing Insert hex wrench into headlamp lock – arrow – . Turn hex socket wrench – 1 – approximately 180 degree in direction of – arrow – (clockwise) in order to release headlamp housing from retainer. Return the headlamp lock – 1 – 90 degree…

Chevrolet/GMC 2500HD 2003 Installation


Filed Under (Chevrolet) by admin on 17-05-2014

Download Overview The installation takes approximately 2 to 3 hours and can be broken down into 5 main steps: 1. 2. 3. 4. 5. Drop front part of headliner Measure/Mark holes for lights Mount Lights Wire Lights Re-assembly Drop Headliner • • Remove sun visor assemblies and sun visor clamp (Torx 15 & 20 required) Disengage passenger side grab handle. Insert small flat screwdriver to pull out covers/lock mechanism then pull out on handle until…

Audi V1 Interface and V1 Power Hardwire Installation Guide


Filed Under (Audi) by admin on 11-12-2012

…planning on placing the V1. Most people put it on the passenger side of the rear view mirror on the windshield. This allows for an easy route for the cables to get under the dash by going around where the windshield and the headliner meet. 2 Place the V1 and plug it in to make sure you leave enough slack to plug the V1 in after routing the cable. 3 Take the V1 back out and start placing the cable. Hold the cable with one hand while using our t…



Filed Under (Chevrolet) by admin on 23-01-2015

Download 1) Take a look at for fit, while you’re glad of the match you are ready to upholster the headliner with fabric. To make sure your complete panel is roofed, allow 2 extra inches of fabric across the entire panel. Use solely a high temp contact spray adhesive (RodDoors Spray Glue Cheese or 3M Tremendous 90). Begin within the center, spray each the again of the material and the front of the panel; 2 sq. feet at a time. Take your time. If…

New Beetle Power Steering Gear Removal and Installation Volkswagen 1998-2008 :- Engine.


Filed Under (Volkswagen) by admin on 23-04-2014

…and the surrounding area before disconnecting. If repairs will not be carried out immediately, place removed parts onto a clean surface and cover. Only use lint-free cloths. Only unpack replacement parts immediately prior to installation. Only use parts in their original packing. Removing Remove bolts – 1 – . Remove cover – A – . Remove bolt – 1 – from universal joint. Remove universal joint from steering gear. Clamp off hose from reservoir usin…



Filed Under (Audi) by admin on 11-04-2015

…om the ECU. As this is done, the harness connector will pull away from the ECU. The reinstallation of the ECU is the reverse of the removal. Step 5 Installing the Fuel Pressure Regulator. Depending on the ECU version of your Beetle, an upgraded FPR may be required. The following steps will illustrate the process. Begin by remove the engine cover, then expose the engine cover screws by removing the dust caps. Remove the bolts securing the engi…

New Beetle Instrument panel removing and installing Volkswagen 1998 – 2005 : Installation.


Filed Under (Volkswagen) by admin on 28-03-2014

download WARNING! Disconnect battery Ground (GND) strap before working on electrical system, observing all cautions => Repair Manual; Electrical; Repair Group 27, Battery, disconnecting and reconnecting. Removing Note: Before disconnecting battery Ground (GND) strap obtain security code for radio with anti- theft coding. Remove driver’s airbag unit => page 69-50. Remove steering wheel => page 69-61. Note: For vehicles with steering an…

New Beetle Oil pan removing and installing Volkswagen 1998 – 2005 :- Installation.


Filed Under (Volkswagen) by admin on 30-03-2014

download Special tools, testers and auxiliary items required Jointed wrench 3185 Socket T10058 Torque wrench V.A.G 1331 Hand drill with plastic brush Protective goggles Flat scraper Silicone sealing compound D 176 404 A2 Locking fluid D 000 600 A2 Removing Remove center and right sound insulation Engines with oil pan protection Body Exterior – Repair Group 50. Remove bolts – 2 – and take sleeves – 3 – off front and rear parts of oil pan protec…

BMW Carsoft 6.5 Software Installation Instruction


Filed Under (BMW) by admin on 03-05-2015

Download BMW Carsoft 6. 5 Software Installation procedure: Step 1: Copy the whole BMW Carsoft 6.5 File folder from the software driver CD to your hard-disk driver D or other hard driver. It is more stable and reliable to install the BMW Carsoft software from hard-disk directly. Step 2: In the hard-disk driver where you pasted the whole BMW Carsoft 6.5 software, please open the File folder of BMW Carsoft 6.5, then double click “SETUP CAR SOFT.ex…